Brentwood, TN · Phones answered 7 AM to 10 PMCall: (615) 437-7061

Garage Door Spring Repair

A snapped spring leaves the full weight of the door on the cables and the opener, so keep it closed and let us change the spring and rebalance it.

A broken garage door spring means the door has lost its counterbalance, and the opener, which was never sized to lift a whole door, cannot make up the difference. On a torsion door the springs wrap a steel shaft over the header; on an extension door they stretch beside each overhead track, with a safety cable threaded through the coil to catch the pieces if one lets go. Either way the replacement has to fit the door: its weight, wire size, length, inside diameter and number of turns all matter, and DASMA notes that a spring that does not match the door shortens the life of the door and its motor.

That is why we weigh and measure the door instead of copying the old spring by eye, which only repeats a mistake if the door was ever mis-sprung. We wind to the turn count the door maker specifies, set the stretch so the coils do not rub, and finish by checking that the door stays at three to four feet off the floor when released. Springs hold serious stored energy, so winding is work for a trained technician, not a weekend project.

Signs You Need Garage Door Spring Repair

  • A bang from the garage, then a door that will not lift
  • A split you can see in the coil of the torsion spring
  • The opener groans and the door rises only a few inches
  • The door feels like dead weight when raised by hand
  • The door lifts, then falls back when you release it
  • Orange rust or pitting along the spring surface

⛈️ The Middle Tennessee Storm Factor

Moisture is the quiet enemy of a spring in this climate. DASMA's cycle-life sheet explains that rust thins the wire and that corrosion pits let fatigue cracks start and spread, which cuts the spring's life. The Nashville airport station logs measurable precipitation on about 123 days a year and temperatures of 90 degrees or higher on 54 days, so a closed, unvented Middle Tennessee garage spends much of the year damp and warm. We look for freckled or pitted coils before we look at the break, and we follow the door maker's lubrication instructions because DASMA links regular greasing to longer spring life.

How We Handle It

Step 1

Weigh and measure

Door weight, wire size, spring length, inside diameter and shaft type are measured, not guessed.

Step 2

Exact quote first

The correct spring set for that door is priced on site, and nothing is unwound until you agree.

Step 3

Wind to specification

Springs go on with the door maker's turn count, then the shaft, cable drums and set screws are checked.

Step 4

Balance proof

The door is released at waist height and must hold; only then is the opener reconnected and tested.

Garage Door Spring Repair — FAQs

If one garage door spring breaks, should both be replaced?

On a door with two springs, yes. Both springs are the same age and have worked through the same cycles, so the second is usually close behind, and a mismatched set can leave the door out of balance.

Why did my garage door spring break?

A garage door spring breaks from metal fatigue that builds with every trip, and rust speeds it up: DASMA notes that corrosion pits start fatigue cracks. DASMA adds that a spring that does not match the door shortens the life of the door and its motor, and that a wrong turn count puts extra force on other counterbalance parts.

Is it all right to haul the door up by hand once a spring has broken?

Do not force a garage door that has a broken spring. DASMA's user checklist is explicit that the door stays unused until the spring is replaced, since the full weight then rides on the cables and the opener. If a car is trapped, call us and we will free it safely.

How long do garage door springs last?

A garage door spring lasts for its rated number of cycles, where one cycle is one open and one close. A household that uses the door many times a day reaches the rating years before a quiet household does, and dampness, skipped lubrication and a wrongly sized spring all shorten it.

Should a homeowner try changing a torsion spring?

No, replacing a garage door spring is not a homeowner job. The DASMA user checklist says springs and spring hardware are under high tension and that all repairs and adjustments must be done by a trained door systems technician with proper tools and instructions.

Old Hickory Boulevard office, Brentwood

Book a garage door repair

Tell us the symptom in plain words (a spring that snapped, a door hanging crooked, a remote that quit) along with your street and town. The arrival window is agreed on the call, and the price is confirmed with you on site before the first part comes off.

Where to find us

Get a free estimatePhone the team

Directions, email and the longer form are on the Parthenon contact page, and every repair we handle is described in the services overview.

Prices to start from

Garage Door Spring Replacementfrom $150 per spring
Garage Door Cable Replacementfrom $150 per cable
Roller Replacementfrom $120 per set
Track Repair & Off-Track Doorfrom $150 per door
Garage Door Opener Repairquoted on site after we check the brand and model
Panel Replacementquoted on site after we match the model and color
Diagnostic Service Call$0 with a completed repair

Each figure is where a job of that kind begins. Spring size, door weight and the parts your door needs set the final number, and we tell you that number before any work begins.

Photos of garage door work

Installer on a stepladder adjusting the opener rail over a white windowed door
Installer setting the overhead track of a tan garage door
Two installers on ladders fitting the left and right tracks of a white door
☎